2004 Custom made off road trailer
with Customline tent

one of a kind
plenty of accessories

trailer features

fully custom 6x4 trailer with 650mm high sides
genuine Toyota Landcruiser running gear
fully TIG seam welded
full 2.1mm BHP chequer plate construction
2.1mm RHS upper frame
any part of the trailer is designed to be able to withstand the entire weight of the trailer
chassis is 3.5mm 50x50 BHP RHS frame including gussets and wheel arch braces
full length drawbar (extending behind the axle) 75x100x3mm BHP RHS
custom suspension using 60-series Landcruiser rear leaf springs and greasable shackles with poly bushes
custom precision machined 50mm axle with genuine 60 Series Landcruiser bearings and brakes
NOT just Landcruiser "bolt pattern" but it actually uses the full Landcruiser hub, axle and brake set - the axle set alone was over $1000
hydraulic overrider type brake setup with ORAC type 360 degree coupling with oversize cylinder
Tare 650kg + load - VERY solid, and tows well
tent top is 2.1mm 50mm RHS, 2.1mm chequer plate and 18mm formply construction

tent

customline (Beenleigh QLD) Bradmill 15oz Australian canvas top & annex
15oz roof and walls
PVC floor
9ft tent
8ft annex
full set of Supapeg poles, pegs and ropes etc
full flip-up tent section for easy packing
stainless steel boxed "kitchen" (stove, cupboard and drawers) mounted on drawbar with 8mm high tensile pins
70litre 304L TIG welded stainless steel watertank with Nitto coupler filler via stainless ball valve (not standard type - designed to be pressure filled from garden type fitting)
2x jerry can holders / brackets
aluminium toolbox and pole carrier (150mm PVC) on front
Johnson 3.4GPM water pump with brass Nitto (quick-connect) fittings - permanently plumbed to tank.
We use a hose and trigger-type garden gun as the water spigot (included)
Double 8" inner-sprung mattress
marine grade carpet liner in the trailer section
2x  Al-Ko wind down hinge-type rear stabilizers stitch TIG welded to frame
stove attached to the kitchen is a Coleman dual-fuel 3-burner

electrical

2x Trojan type 205Ah GC2 group size batteries in 2.1mm chequer-plate boxes - around 12 months old
Plasmatronics PL20 solar charge controller
interior "Jaycar" white LED strip permanently attached to centre hoop and switched from under bed
interior Canon type 10A and cigarette lighter 10A type sockets
10A Canon (Amphenol) type 3-pin socket internal to trailer body (for fridge)
2x Amphenol / Canon type sockets & 2 x 10A cigarette lighter type sockets on outside of trailer
blue "Power On" LED which doubles as a convenient area light
Johnson 3.4GPM water pump with brass Nitto (quick-connect) fittings - permanently plumbed to tank
We use a hose and trigger-type garden gun as the water spigot
internal Narva fluro light for trailer body (great for unpacking at night etc)
50A Anderson plugs x3 - 1 x drawbar, 2 x side (1 x solar panel input + 1 x batt charger input)
Sunraysia 15" rims with 31" Maxxis A/T tyres

fit & finish

95% stainless steel fasteners used throughout (only where there is a specific strength application - such as the hitch and top hinges) have there been other types of fasteners used. Particularly these are grade 8.8 high tensile
Dulux QuitRust enamel colour coat (3 coats applied)
Dulux QuitRust zinc coating on undercarriage
BodyTech bituminous sealer applied to undercarriage

$8,650

 
contact Jon in Redland Bay QLD
0418875035
jon.luthjeatgmail.com

please copy & paste e-mail address & replace at with @